iVIGA Kais Factory Supplier
Prepare the installation tools and check whether the supporting parts are complete before installation. Common faucet parts are: hoses, rubber washers, da dej, drains, tus pas nrig, decorative caps, lwm.
Installation of single-hole basin faucet
When buying a single-handle basin faucet, you should pay attention to the diameter of the spout. Niaj hnub no, feem ntau ntawm cov dej hauv kev ua lag luam belongs rau cov yeeb nkab tawv, so you should pay attention to the height of the upper spout. It is appropriate to go down from the basin 35 work points**. Thaum lub sij hawm installation, yuav tsum xaiv lub kaum sab xis tshwj xeeb, thiab lub kaum sab xis valve yuav tsum tau kho rau cov kav dej kub thiab txias los ntawm phab ntsa. Thaum koj pom tias muaj kev ncua deb ntawm lub kaum sab xis thiab cov yeeb nkab dej ntawm lub faucet, buy a special extension pipe to connect it. Nco ntsoov, you must not use other water pipes to connect, vim yog dej siab siab, nws yuav yooj yim poob tawm thiab xau dej, causing you loss. Yog hais tias cov yeeb nkab inlet ntev dhau los ntawm lub qhov hluav taws xob cov yeeb nkab, ib feem tuaj yeem txiav tawm raws li koj xav tau. Yog lub kaum sab xis tsis tsim nyog, koj tuaj yeem khoov nws mus rau txoj haujlwm koj xav tau. Nco ntsoov: Do not bend hard to 90 degrees or more than 90 qib. Thaum txhim kho lub phiab kom ntws, please don’t forget to purchase the small connector of the faucet (short-circuit the faucet). Thov tsis txhob hnov qab yaug cov yeeb nkab dej faus rau hauv phab ntsa ua ntej koj nruab.
Installation of shower and bathtub faucet (wall hanging)
After you have purchased a shower, lub dab dej, or wall-mounted faucet, you can choose a suitable height to bury the water pipe. The distance between the hot and cold water pipes must reach 15 cm. Ua ntej installation, you must not forget to flush the water pipe to prevent the water from being too hard and causing damage to the faucet.
Concealed shower and bathtub faucets: After purchasing a concealed faucet, the valve core of the faucet is generally pre-buried in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the valve core will not be embedded. Do not remove the plastic protective cover of the valve core easily during pre-embedding, so as to avoid damage to the valve core by cement and other chores. Ntxiv rau, you should pay attention to the up and down, left and right directions of the spool when embedding the spool to avoid the wrong spool. When the wall-mounted faucet is pre-embedded in the water inlet pipe, there is a deviation in the size, and the adjustable crutches can be used to adjust the position.
Installation of thermostatic faucet
Ua ntej txhim kho lub thermostatic faucet, please check if the water pipes are hot on the left and cold on the other. Remember not to connect the hot and cold water pipes wrongly to avoid the faucet not working properly. Gas thiab hnub ci dej rhaub dej tsis tuaj yeem siv cov faucet thermostatic vim tias cov dej siab tsawg dhau. Tsis txhob hnov qab txhim kho cov dej kub thiab dej txias thaum txhim kho cov faucet thermostatic.
