विभिन्न प्रकारका नलहरूको स्थापना बिन्दुहरू

Prepare the installation tools and check whether the supporting parts are complete before installation. Common faucet parts are: नली, rubber washers, वर्षा, नालीहरू, crutches, decorative caps, आदि.

Installation of single-hole basin faucet

When buying a single-handle basin faucet, you should pay attention to the diameter of the spout. आजकल, बजारमा अधिकांश पानी कडा पाइपको हो, so you should pay attention to the height of the upper spout. It is appropriate to go down from the basin 35 work points**. स्थापना को समयमा, एक विशेष कोण वाल्व चयन गर्नुपर्छ, र कोण भल्भ भित्ताबाट तातो र चिसो पानीको पाइपहरूमा फिक्स हुनुपर्छ. जब तपाईंले फेला पार्नुभयो कि नलमा कोण भल्भ र पानीको पाइप बीचको दूरी छ, buy a special extension pipe to connect it. सम्झनुहोस्, you must not use other water pipes to connect, किनभने पानीको चाप उच्च छ भने, यो सजिलै झर्नेछ र पानी चुहिनेछ, causing you loss. यदि इनलेट पाइप आउटलेट पाइप भन्दा धेरै लामो छ, भाग आफ्नो आवश्यकता अनुसार काट्न सकिन्छ. यदि कोण उपयुक्त छैन, तपाईं यसलाई आवश्यक स्थितिमा झुकाउन सक्नुहुन्छ. सम्झनुहोस्: Do not bend hard to 90 degrees or more than 90 डिग्री. निकास गर्न बेसिन स्थापना गर्दा, please don’t forget to purchase the small connector of the faucet (short-circuit the faucet). कृपया तपाईंले यसलाई स्थापना गर्नु अघि भित्तामा गाडिएको पानीको पाइप फ्लश गर्न नबिर्सनुहोस्.

Installation of shower and bathtub faucet (wall hanging)

After you have purchased a shower, बाथटब, or wall-mounted faucet, you can choose a suitable height to bury the water pipe. The distance between the hot and cold water pipes must reach 15 सेमी. स्थापना गर्नु अघि, you must not forget to flush the water pipe to prevent the water from being too hard and causing damage to the faucet.

Concealed shower and bathtub faucets: After purchasing a concealed faucet, the valve core of the faucet is generally pre-buried in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the valve core will not be embedded. Do not remove the plastic protective cover of the valve core easily during pre-embedding, so as to avoid damage to the valve core by cement and other chores. साथै, you should pay attention to the up and down, left and right directions of the spool when embedding the spool to avoid the wrong spool. When the wall-mounted faucet is pre-embedded in the water inlet pipe, there is a deviation in the size, and the adjustable crutches can be used to adjust the position.

Installation of thermostatic faucet

थर्मोस्टेटिक नल स्थापना गर्नु अघि, please check if the water pipes are hot on the left and cold on the other. Remember not to connect the hot and cold water pipes wrongly to avoid the faucet not working properly. ग्यास र सोलार वाटर हिटरहरूले थर्मोस्टेटिक नलहरू प्रयोग गर्न सक्दैन किनभने पानीको चाप धेरै कम छ. थर्मोस्टेटिक नल स्थापना गर्दा तातो र चिसो पानी फिल्टर स्थापना गर्न नबिर्सनुहोस्.